Activity Stream

Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Articles Articles Groups Groups
  • LegnumPower's Avatar
    Today, 10:31 PM
    Is there any place where to buy the rear propshaft bearing for the Legnum (MR246695), now that Mitsubishi has discontinued the part?
    0 replies | 3 view(s)
  • ianturbo's Avatar
    Today, 10:30 PM
    This happened to me with a new battery i purchased, poles were on the opposite side . It was throwing it down .I blew the main fuse , i had to break off the plastic cover and bend it over to make contact while i ordered one off ebay . Sent from my SM-A705FN using Tapatalk
    1 replies | 22 view(s)
  • ianturbo's Avatar
    Today, 08:26 PM
    Could I put a feed to the relay on the inner wing to power up the pump to prime it ?? ian
    74 replies | 1602 view(s)
  • JWerts74's Avatar
    Today, 01:14 PM
    Hi guys so I'm moving house next week and haven't touched the old girl in a while so decided to prepare her for the move. Now I unfortunately have broken a wrist and torn at least a few ligaments in my knee so I had my mum help me......... This is where the problem is she connected the jump leads ,I think we can see where this is going, turns out she put them the wrong way round. So the extent of the damage so far seems to be limited to the large 120A fuse for the battery.I've had a quick look...
    1 replies | 22 view(s)
  • sonnick84's Avatar
    Today, 09:40 AM
    sonnick84 posted a visitor message on sonnick84's profile
    Практически всё, что творится в мире, прямо или косвенно влияет на на всех нас. Следует уходить от политики? Как ни крути, держаться в тени сейчас, трудно. Потому что политическая информация позволяет принять грамотные решения в сложны ситуациях. Новостных источников в данное время большое количество и можно вполне отказаться от таких вариантов, как телевизор или газета. Можно порекомендовать новости телеграм каналов. Это на самом деле очень удобно, все самое важное и актуальное рядом. Во...
  • 3D laten's Avatar
    Today, 05:58 AM
    3D laten posted a visitor message on 3D laten's profile
    3d laten printen
  • Blackbandt's Avatar
    Yesterday, 03:07 PM
    Davezj takes the time you need. However, I also believe that most do not drive 1.6 bar Boost. As I said I have very strong interest in a complete kit and would like to buy one from you. There was also another user who offers a complete kit but that is very expensive. Possibly you can write with him times as he has solved the problem with the boost. in the OzVR4 forum the guy is called naughtika
    19 replies | 503 view(s)
  • adaxo's Avatar
    Yesterday, 08:24 AM
    Missfire at this high boost is not necessarily the coil pack problem, Btw you should aim to offer factory replacement setup which work as should in factory standard conditions then you have no problem with ppl blowing 1.5bar and complaining about your kit, great you aim so high but there always going to be an issue if you push anything to or even well over the limit. Most of us want working ignition setup on mild boost setting anyway.
    19 replies | 503 view(s)
  • Davezj's Avatar
    Yesterday, 01:18 AM
    the reason for me making the COP kit is because the standard mitsi coil packs are stupidly expensive at about £160-£180 each, if you can evern buy them any more as i believe mitsi have stopped producing the standard coil packs so all the one you can buy now are new old stock and they will run out very quickly. my coil packs on the VR4 are failing and i needed to replace them for my own use. so i thought if i need and COP kit then other people will need a COP as well. but there is a massive...
    19 replies | 503 view(s)
  • Marxus's Avatar
    05-05-2021, 07:49 PM
    Sorry for necro, but I was looking for the same part numbers and with help of ASA and this thread I made this list. Probably it won't help anybody. But if it helps only one person someday the effort was not in vain. - Galant and Legnum share the same front (obviously). For the rear overfenders (RR LH + RH) for Legnum please look at the bottom of this list. - The Pads for the rear fender are the same for Galant and Legnum. - I have not found white pads as well as blue. Probably the...
    3 replies | 150 view(s)
  • Blackbandt's Avatar
    04-05-2021, 06:04 PM
    I would definitely take a complete kit Please
    19 replies | 503 view(s)
  • Louis's Avatar
    04-05-2021, 04:07 PM
    Put me down for a full kit please :) Its been on my list to do for a while, but just haven't got round to it.
    19 replies | 503 view(s)
  • Confused's Avatar
    04-05-2021, 10:34 AM
    Hey Kev! That's brilliant!
    1 replies | 47 view(s)
  • Davezj's Avatar
    04-05-2021, 01:09 AM
    i an ship to anywhere in the world at the your expense. i have not worked out the exact cost, i have enough parts for 4 full kits with coil packs. i am hoping the kit will come in about £200 for full kit with 6 coil packs. this is just a rough guess as i will have to go through all my paper work and do a proper costing i will offer the kit without coil packs. Just wiring harness, mounting brackets and nuts bolts washer. i will offer the kit as wiring harness only. i have got a lot...
    19 replies | 503 view(s)
  • 94000 Miles's Avatar
    04-05-2021, 01:00 AM
    Hi all, Can someone start a new thread in the Resource Library say under "Articles Library" for the "VR4 Power Steering Rack Overhaul" I've just finished the guide and haven't permission to "post new threads" Once done I'll post in there the PDF guide. It's 24Mb Kev
    1 replies | 47 view(s)
  • Blackbandt's Avatar
    02-05-2021, 12:56 PM
    what would the cop kit set then cost with you ? And would you ship to Germany?
    19 replies | 503 view(s)
More Activity