OSiRiS
30-05-2006, 11:15 PM
FS: EAUDIO 300wRMS AMP and DIGITAL DESIGNS 6.5" COMP SPEAKERS w/ TWEETERS both NEAR NEW $400
These make a perfect combo! Near new, very little use. Same setup in my car at the moment, selling these because they are just a spare set so I can give you a demo on clarity and volume etc.
People in the car audio circles will know these.
Any questions etc. please ask.
Free shipping anywhere in NZ :)
280AB
2 Channel Power Amplifier
http://www.eaudio.co.nz/280ab_small.jpg (http://www.eaudio.co.nz/280ab.jpg)
12dB/Octave crossovers 50Hz-5kHz, Highpass / Lowpass
Detented crossover frequency potentiometers
Balanced differential RCA input
Speaker level input
0.1 - 10V input sensitivity with 12dB input attenuator
Buffered RCA level output with crossover
Bass EQ centered at 40Hz, 0 - 12dB
Mosfet power supply
Thermal and short circuit protection
4 gauge power inputs, 8 gauge speaker outputs
Dimensions:248(W) x 52.5(H) x 180(L)mm
DD C6.2
6 1/2 inch Component Set
http://www.hotwire.net.nz/skinHotwire/siteImages/speakers/Digital_Designs/DD6.2_fs.jpg
These new DDSeperates offer unsurpassed installation flexibility and an excellent upgrade to sound quality at a price that will please any system budget. These DDSeperates can be mounted in several ways, as a traditional coaxial driver, a surface mounted tweeter or flushmounted tweeter with separate woofer.
High quality parts are used throughout the drivers. The surrounds are from a high loss but light weight rubber to smooth the frequency response and keep the sensitivity as high as possible. The surround is attached to an injection molded, mineral filled polypropylene cone. This makes a rigid cone with good internal damping. A billet machined aluminum phase plug helps to correct the upper midrange response when used as a seperate woofer.
The voice coil uses the highest temperature wire available wound on a polyimide coil former. The machined motor structure helps keep the tolerances tight while providing the high energy magnetic strength needed for today's high output demands.
The tweeter is a 25mm, neo magnet system with liquid cooling. The metal alloy diaphram provides smooth response by moving breakup modes beyond the audible frequency range. The lightness of the diaphram contributes to higher sensitivity and less strain at a given volume.
The crossover uses high power handling parts, film capacitors and high voltage electrolytics. The laminated steel coils keep resistance low, cutting output losses to a minimum. A solid state fuse helps to keep the system safe when accidental overloads occur. The connections are gold plated to prevent corrosion.
The kits come with everything needed to mount in just about any situation. Speaker grills are provided for surface mount applications. The tweeters come with a surface mount, angled housing, a flushmount housing and a pole piece mount for coax applications. Included are two crossovers, speaker wire and mounting tabs/screws.
The new DDSeperates bring highend performance within reach of any enthusiast, giving high value, ease of installation and high fidelity.
These make a perfect combo! Near new, very little use. Same setup in my car at the moment, selling these because they are just a spare set so I can give you a demo on clarity and volume etc.
People in the car audio circles will know these.
Any questions etc. please ask.
Free shipping anywhere in NZ :)
280AB
2 Channel Power Amplifier
http://www.eaudio.co.nz/280ab_small.jpg (http://www.eaudio.co.nz/280ab.jpg)
12dB/Octave crossovers 50Hz-5kHz, Highpass / Lowpass
Detented crossover frequency potentiometers
Balanced differential RCA input
Speaker level input
0.1 - 10V input sensitivity with 12dB input attenuator
Buffered RCA level output with crossover
Bass EQ centered at 40Hz, 0 - 12dB
Mosfet power supply
Thermal and short circuit protection
4 gauge power inputs, 8 gauge speaker outputs
Dimensions:248(W) x 52.5(H) x 180(L)mm
DD C6.2
6 1/2 inch Component Set
http://www.hotwire.net.nz/skinHotwire/siteImages/speakers/Digital_Designs/DD6.2_fs.jpg
These new DDSeperates offer unsurpassed installation flexibility and an excellent upgrade to sound quality at a price that will please any system budget. These DDSeperates can be mounted in several ways, as a traditional coaxial driver, a surface mounted tweeter or flushmounted tweeter with separate woofer.
High quality parts are used throughout the drivers. The surrounds are from a high loss but light weight rubber to smooth the frequency response and keep the sensitivity as high as possible. The surround is attached to an injection molded, mineral filled polypropylene cone. This makes a rigid cone with good internal damping. A billet machined aluminum phase plug helps to correct the upper midrange response when used as a seperate woofer.
The voice coil uses the highest temperature wire available wound on a polyimide coil former. The machined motor structure helps keep the tolerances tight while providing the high energy magnetic strength needed for today's high output demands.
The tweeter is a 25mm, neo magnet system with liquid cooling. The metal alloy diaphram provides smooth response by moving breakup modes beyond the audible frequency range. The lightness of the diaphram contributes to higher sensitivity and less strain at a given volume.
The crossover uses high power handling parts, film capacitors and high voltage electrolytics. The laminated steel coils keep resistance low, cutting output losses to a minimum. A solid state fuse helps to keep the system safe when accidental overloads occur. The connections are gold plated to prevent corrosion.
The kits come with everything needed to mount in just about any situation. Speaker grills are provided for surface mount applications. The tweeters come with a surface mount, angled housing, a flushmount housing and a pole piece mount for coax applications. Included are two crossovers, speaker wire and mounting tabs/screws.
The new DDSeperates bring highend performance within reach of any enthusiast, giving high value, ease of installation and high fidelity.