workshop day attendies, this sunday

[Gly]

just a quick pole to see how many are coming this sunday,

also if you could state the job (if any?) you would like done,

also any tools you can bring
(id like to see if i need to buy any or if theres someone i can borrow from)


myself i would like to get my transfer case and rear diff fluid changed

and ill be bringing a couple of socket sets,
ring spanners, a jack or two, 2 sets of axel stands, a few screw drivers,


also anyone have open ended ring spanners like these?
http://www.trademe.co.nz/Browse/Listing.aspx?id=87568724

i will have to buy some if no one has a set to bring.

[You See]

I'll be there....just the camber fix-a-ma-callit for me. :)

[SirVr4]

Need nothing done just coming mainly to meet and greet put faces to names and help out where ever.

also pick at brains for possible this to do to my ride

[bradc]

Fit new passenger side front door, new right rear speaker. Plus the wheel swap with someone that has brembo's

[dickytim]

fitting amps to spare wheel well.

Will be bringing;

Full tool kit
Gear wrench set
Drill and drill bits
Jig saw
Electric screwdriver
Various wiring bits and pieces and terminals

Anyone with holes saws or a skil saw I would appreciate it.

[Kenneth]

Attending. (myself and Jo) till about 5:30pm

Nothing really to do except help I guess.

Can bring soldering iron and some tools
ramps
big syringe thinggy for oil. It needs a somewhat thinner hose on the end really though.

Carsten, you want me to bring the map-ecu?

[Joanne]

Attending. (myself and Jo) till about 5:30pm

Not sure what I'm going to be doing (other than just being my beautiful self) - so I'm sure you lot can direct me as need be...

[You See]

Not sure what I'm going to be doing (other than just being my beautiful self) - so I'm sure you lot can direct me as need be...
Aren't we having a feed?....I'm sure there'll be some eggs you can cook us Jo! /pan

[bradc]

yeah Jo can be the cook :)

[Spirit]

Don't forget lots of /Camera

[NAUSED]

i wouuld love to but the only way would be if i had a lift, cause well no point of hiding it, i lost my license /Grrr .

and where bouts is it?

[william]

Change spark plugs

Rewire boost guage

Chat to Mpau009 about the MAP ECU2!

Bring ramps, airtools, general tools including sparkplug spanner, soldering iron, skill saw, something for the BBQ. Anything else?

[GroundControl]

Don't forget lots of /Camera

I should be there (and I'll take my camera).

I'd like to get a boost gauge installed (which reminds me, I really should go buy one)

[mpau009]

Chat to Mpau009 about the MAP ECU2!
:2thumbsup


I'll be there for sure.

My list includes:
-Have a look at the camber and awful noises from the back:thinking:
-With guidance, have a look at the clutch, and hopefully find some miracle solution
-Take out my dodgy old LH headlight, replace, and butcher the old one for a potential air intake
-Convince everyone other than Brad to go in for the MAP2 buy:afro:

[Joanne]

Aren't we having a feed?....I'm sure there'll be some eggs you can cook us Jo! /pan


Let me think on that offer for a while.... no :D

I don't mind helping with them car things /toycar Plus Kenny and I have to be off just before 6 to play football :)

[Joanne]

i wouuld love to but the only way would be if i had a lift, cause well no point of hiding it, i lost my license /Grrr .

We can give you a ride :)

[Kenneth]

i wouuld love to but the only way would be if i had a lift, cause well no point of hiding it, i lost my license /Grrr .

and where bouts is it?
We can give you a ride :)

Yep :) cant gaurentee a lift home though... we have to be in the city by 6:25pm or something

[SHOWVR]

SO far its installing a boost gauge and sneaky manual mode.

Brad - you still providing meat and stuff?

can someone giveme directions to te irirangi gull. cheers

[bradc]

Don - there will be some meat provided, not huge amounts though.

[KiwiTT]

Just the car and some tape. Might try to get some cable ties. See if that can help the underside of the car from dropping down too much.

[SHOWVR]

Don - there will be some meat provided, not huge amounts though.
well if you want ill bring some sausages

We should all be chipping in something, since brad is providing the venue the least we could do is provide some tucker?
Or we could use the miilions in our club account? :inquisiti

[Lucas]

I'll be doing the rear camber fixa-me-mod and now I'll also be hard wiring in a new (2nd hand) radar detector.

I'll be bringing:
30-40cm power bar 1/2" drive
Wire strippers
Gas soldering Iron
Battery drill - no bits coz they're all shot!
Cable ties
Sausages or something

[bradc]

Cool thanks Don :)

Lucas, not much need to bring cables ties, I've got about 500 here. It's all appreciated though.

[Lucas]

It's just that I've always got them in my toolcase. On that note I will also have an assortment of heatshrink (both glue lined and normal) as well as crimp lugs but I don't know that there would be all that much use for them, you never know though...

[KiwiTT]

Cool thanks Don :)

Lucas, not much need to bring cables ties, I've got about 500 here. It's all appreciated though.Thanks Brad. Saves me a trip to the store.

[Subaru ETA]

just a quick pole to see how many are coming this sunday,

also if you could state the job (if any?) you would like done,

also any tools you can bring
(id like to see if i need to buy any or if theres someone i can borrow from)


myself i would like to get my transfer case and rear diff fluid changed

and ill be bringing a couple of socket sets,
ring spanners, a jack or two, 2 sets of axel stands, a few screw drivers,


also anyone have open ended ring spanners like these?
http://www.trademe.co.nz/Browse/Listing.aspx?id=87568724

i will have to buy some if no one has a set to bring.

what sizes of pipe spanner you need? i have some but not many...think left them in various customers cars!

[Gly]

i may need a 10mm open ended ring spanner so i can change my rear brake lines,
stupid soft metal fittings!

[ShadyNZer]

umm just the decat and if able solder my boost gauge wires....

Gly - still able to get those decat bolts off you bro?

umm prolly bring some sizzlers or something.....:thumbsup:

[Gly]

yep,

txt me tomorrow to find some,
i know i had a few to spare,

021-104-5215

[Subaru ETA]

just popped into work but cant find 10mm pipe spanner.... anyone want me to bring a rattle gun, axle stands or anything?

[KiwiTT]

Sounds like a good idea. It may be useful, check the list of jobs people are doing on the top of this thread (http://www.clubvr4.com/forum/showthread.php?t=21583)