SquattingDog
14-12-2009, 09:45 AM
Amplifiers:
The Soundstream unit is second-hand (but top-class), and the Polk Audio units I bought through my business (Eclipse Computers), which are brand new, but will come without warranty as they were purchased from a supplier who went into receivership. A tax invoice will be supplied. MODS - if this is inappropriate, or not acceptable, please tell me, and I will edit these out, however I really need to move these as they are soaking up my capital, and I figured that helping the CVR4 community out with some cheap, quality hookups could work well
Soundstream PCA1000D Picasso-Series $550 incl courier (Nationwide)
Specs:
1000W RMS D-Class Amplifier (1000W RMS @ 1Ohm, 800W RMS @ 2Ohms, 500W RMS @ 4Ohms)
RCA in- and outputs for daisy-chaining amps
Soundstream's propietary system for running two of these units in parallel to drive a single sub
Have used this to drive the 12" Rockford recently and prior to drive a 1000W 15" Soundstream T4-15 which made 130+dBA
Looks really good in chrome finish - could do with a polish. Goes really hard, and is extremely compact!
The 40mm cooling fan needs looking at, whines sometimes, but has no issues running subs.
Bought from Parallel for $1100 approx 2.5yrs ago.
No longer hooked up - photos taken when still in car.
http://eclipsecomputers.co.nz/temp_i...PCA1000D-0.jpg
http://eclipsecomputers.co.nz/temp_i...PCA1000D-1.jpg
http://eclipsecomputers.co.nz/temp_i...PCA1000D-2.jpg
2x Polk Audio PA500.4 500W RMS 4-Channel Amplifiers $265 each
Specifications:
125 watts x 4 continuous, 200 x 4 dynamic power (2 ohm load), 4 channel mode.
250 watts x 2 (4 ohm) continuous power, 2 channel mode.
CEA-2006 Compliant specifications for true, accurate power ratings.
4-channel, dual bridge-mono (2-channel), or dual simultaneous stereo/mono operation provide a variety of configurations and setups: 4-channel for front and rear speakers; 2 speakers and a sub; 2 subwoofers; or 2 subs and 4-channels in passive-tri mode.
2 ohm stable 4-channel operation.
High-speed MOSFET switching power supply and high current Bipolar Output Transistors pump maximum voltage and high current to your speakers or subwoofers.
Double Layer Fiberglass Epoxy Printed Circuit Boards for more rigidity, less shrinkage and a smaller overall amp footprint.
6-Way Smart System Protection (SSP) circuits
Fully adjustable (50- 500Hz) 12 dB/octave high- or low-pass crossover. Defeatable for full range (flat) operation.
Switchable 8 dB bass boost at 40Hz for extra bass thump.
Variable input gain optimizes match with different signal sources (250mv to 7.5V).
RCA Outputs (front channels only) for easy daisy chaining of other amplifiers.
Mounting hardware with rubber isolation grommets and extra fuses included.
Light Bar/Fan Output- Connect an optional LED light bar or cooling fan for custom installations.
Multi-Color Status LED gives instant information on amplifier operation.
Remote Subwoofer Level Adjuster for rear channels included.
Wicked, clean-sounding amplifiers with great looks. Give out the power they are rated at - high quality componentry inside these units means you can load them up to the max, and run them happily at that setting as long as you want.
Ideal for 4x speakers or 1 - 2x subs (with single or Dual Voice Coils).
http://eclipsecomputers.co.nz/temp_i...io-PA500-4.jpg
Subs:
These are all brand new - I bought up too many for my business, so am letting them go very cheaply. They have no warranty on them as they came from a supplier who went into receivership, but will come with a tax invoice through my company, Eclipse Computers.
2x 10" Shallow Clarion PFW1051 300W RMS subs SOLD
Specifications:
Speaker Size: 10" (25cm)
Power Handling: 600W Peak, 300W RMS
Voice Coil: 4-Ohm SVC (Single Voice Coil)
Magnet: Strontium Ferrite
Terminals: Gold Plated
Cone: Kevlar/Paper design
Dimensions: 255.5mm Diameter, 75mm Depth
RRP: $289.99
Ideal for sitting inside the spare wheel of a VR4, with a box on top, under the carpet. Sodge has this set up in his VR4, ask him about it. I am also running one of these in the back of the RVR, as it only requires a 16L box - gives me heaps of space and cranks out great sound. I listen to a range of music, including hip hop/rnb - yes 10" subs are still good for this.
http://eclipsecomputers.co.nz/temp_i...on-PFW1051.jpg
1x 10" Clarion PXW1052 500W RMS sub $120
Specifications:
Speaker Size: 10" (25cm)
Power Handling: 1000W Peak, 500W RMS
Voice Coil: 4-Ohm DVC (Dual Voice Coil)
Magnet: Dual Strontium Ferrite
Terminals: Gold Plated
Cone: Kevlar/Paper design
RRP: $325.00
For more power, or running a 2Ohm load on an amp - get this 10" with Dual 4 Ohm Voice Coils.
http://eclipsecomputers.co.nz/temp_i...nPXW1252-0.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-1.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-2.jpg
2x 12" Clarion SW1251 350W RMS subs $69 each
Specifications:
Speaker Size: 12" (30cm)
Power Handling: 700W Peak, 350W RMS
Voice Coil: 4-Ohm SVC (Single Voice Coil)
Magnet: Dual Strontium Ferrite
Terminals: Gold Plated
Cone: Fiberglass/Paper design
RRP: $129.99
Because everyone loves 12" subs - ideal boot shakers, great all-round sound, highly recommended in a pair.
http://eclipsecomputers.co.nz/temp_i...ion-SW1251.jpg
4x 12" Clarion PXW1252 500W RMS subs $130 each
Specifications:
Speaker Size: 12" (30cm)
Power Handling: 1000W Peak, 500W RMS
Voice Coil: 4-Ohm DVC (Dual Voice Coil)
Magnet: Dual Strontium Ferrite
Terminals: Gold Plated
Cone: Kevlar/Paper design
RRP: $389.99
For more powerful 12" subs - which everyone loves. Dual voice coils mean running two of these together in parallel gives you a 1Ohm load - ideal for monoblocks (such as the 1KW amp I'm selling also hint hint...). Four of these in one car would be mad!
http://eclipsecomputers.co.nz/temp_i...nPXW1252-0.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-1.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-2.jpg
1x 15" Clarion PXW1552 750W RMS $160
Specifications:
Speaker Size: 15" (39.5cm)
Power Handling: 1500W Peak, 750W RMS
Voice Coil: 4-Ohm DVC (Dual Voice Coil)
Magnet: Dual Strontium Ferrite
Terminals: Gold Plated
Cone: Kevlar/Paper design
RRP: $499.99
For lovers of deep, hard hitting, long bass hits when 12" subs just don't cut it. Dual voice coils let you load up your favourite amp (see the Soundstream on sale at the top of the thread, that pumps 800W RMS @ 2Ohms - ideal!).
http://eclipsecomputers.co.nz/temp_i...nPXW1252-0.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-1.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-2.jpg
Intercooler:
Top-Mount style Intercooler for TD04-15T $30
Factory Intercooler, was used in top-mount set up (top-mounting attachments not included).
Some bent fins on top, but no leaks and works well - designed for use with TD04-15T in RVR X3 factory set up, but good for use with any turbo up to this size (and maybe bigger if you front-mount it).
http://eclipsecomputers.co.nz/temp_i...pMountIC-0.jpg
http://eclipsecomputers.co.nz/temp_i...pMountIC-1.jpg
http://eclipsecomputers.co.nz/temp_i...pMountIC-2.jpg
http://eclipsecomputers.co.nz/temp_i...pMountIC-3.jpg
Turbo:
EVO I TD05-16G Housings, Internal Wastegate, factory oxygen sensor $100ono
EVO I TD05-16G genuine exhaust housing (cracked through to internal wastegate, needs welding up for maximum flow/boost control), factory TD05-16G compressor cover and Internal Wastegate to suit. Factory oxygen sensor still attached to exhaust housing. Ideal to mate up to EVO I - III exhaust manifold flange. Turbine (compressor wheel and exhaust) have been removed for use in my new turbo. Bought this for $450+GST, hope someone gets good use out of the parts remaining Pictures to go up later.
Rain/Wind deflectors to suit RVR/SUV:
Aftermarket Rain/Wind deflectors off RVR $20
Pair of wind-deflectors to suit RVR or other SUV/Van.
Good condition, no cracks, no major scratches, comes with all mounting points.
Have just checked with another potential buyer, do not fit Mitsubishi L200 (Ute).
http://eclipsecomputers.co.nz/temp_i...dsheilds-0.jpg
The Soundstream unit is second-hand (but top-class), and the Polk Audio units I bought through my business (Eclipse Computers), which are brand new, but will come without warranty as they were purchased from a supplier who went into receivership. A tax invoice will be supplied. MODS - if this is inappropriate, or not acceptable, please tell me, and I will edit these out, however I really need to move these as they are soaking up my capital, and I figured that helping the CVR4 community out with some cheap, quality hookups could work well
Soundstream PCA1000D Picasso-Series $550 incl courier (Nationwide)
Specs:
1000W RMS D-Class Amplifier (1000W RMS @ 1Ohm, 800W RMS @ 2Ohms, 500W RMS @ 4Ohms)
RCA in- and outputs for daisy-chaining amps
Soundstream's propietary system for running two of these units in parallel to drive a single sub
Have used this to drive the 12" Rockford recently and prior to drive a 1000W 15" Soundstream T4-15 which made 130+dBA
Looks really good in chrome finish - could do with a polish. Goes really hard, and is extremely compact!
The 40mm cooling fan needs looking at, whines sometimes, but has no issues running subs.
Bought from Parallel for $1100 approx 2.5yrs ago.
No longer hooked up - photos taken when still in car.
http://eclipsecomputers.co.nz/temp_i...PCA1000D-0.jpg
http://eclipsecomputers.co.nz/temp_i...PCA1000D-1.jpg
http://eclipsecomputers.co.nz/temp_i...PCA1000D-2.jpg
2x Polk Audio PA500.4 500W RMS 4-Channel Amplifiers $265 each
Specifications:
125 watts x 4 continuous, 200 x 4 dynamic power (2 ohm load), 4 channel mode.
250 watts x 2 (4 ohm) continuous power, 2 channel mode.
CEA-2006 Compliant specifications for true, accurate power ratings.
4-channel, dual bridge-mono (2-channel), or dual simultaneous stereo/mono operation provide a variety of configurations and setups: 4-channel for front and rear speakers; 2 speakers and a sub; 2 subwoofers; or 2 subs and 4-channels in passive-tri mode.
2 ohm stable 4-channel operation.
High-speed MOSFET switching power supply and high current Bipolar Output Transistors pump maximum voltage and high current to your speakers or subwoofers.
Double Layer Fiberglass Epoxy Printed Circuit Boards for more rigidity, less shrinkage and a smaller overall amp footprint.
6-Way Smart System Protection (SSP) circuits
Fully adjustable (50- 500Hz) 12 dB/octave high- or low-pass crossover. Defeatable for full range (flat) operation.
Switchable 8 dB bass boost at 40Hz for extra bass thump.
Variable input gain optimizes match with different signal sources (250mv to 7.5V).
RCA Outputs (front channels only) for easy daisy chaining of other amplifiers.
Mounting hardware with rubber isolation grommets and extra fuses included.
Light Bar/Fan Output- Connect an optional LED light bar or cooling fan for custom installations.
Multi-Color Status LED gives instant information on amplifier operation.
Remote Subwoofer Level Adjuster for rear channels included.
Wicked, clean-sounding amplifiers with great looks. Give out the power they are rated at - high quality componentry inside these units means you can load them up to the max, and run them happily at that setting as long as you want.
Ideal for 4x speakers or 1 - 2x subs (with single or Dual Voice Coils).
http://eclipsecomputers.co.nz/temp_i...io-PA500-4.jpg
Subs:
These are all brand new - I bought up too many for my business, so am letting them go very cheaply. They have no warranty on them as they came from a supplier who went into receivership, but will come with a tax invoice through my company, Eclipse Computers.
2x 10" Shallow Clarion PFW1051 300W RMS subs SOLD
Specifications:
Speaker Size: 10" (25cm)
Power Handling: 600W Peak, 300W RMS
Voice Coil: 4-Ohm SVC (Single Voice Coil)
Magnet: Strontium Ferrite
Terminals: Gold Plated
Cone: Kevlar/Paper design
Dimensions: 255.5mm Diameter, 75mm Depth
RRP: $289.99
Ideal for sitting inside the spare wheel of a VR4, with a box on top, under the carpet. Sodge has this set up in his VR4, ask him about it. I am also running one of these in the back of the RVR, as it only requires a 16L box - gives me heaps of space and cranks out great sound. I listen to a range of music, including hip hop/rnb - yes 10" subs are still good for this.
http://eclipsecomputers.co.nz/temp_i...on-PFW1051.jpg
1x 10" Clarion PXW1052 500W RMS sub $120
Specifications:
Speaker Size: 10" (25cm)
Power Handling: 1000W Peak, 500W RMS
Voice Coil: 4-Ohm DVC (Dual Voice Coil)
Magnet: Dual Strontium Ferrite
Terminals: Gold Plated
Cone: Kevlar/Paper design
RRP: $325.00
For more power, or running a 2Ohm load on an amp - get this 10" with Dual 4 Ohm Voice Coils.
http://eclipsecomputers.co.nz/temp_i...nPXW1252-0.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-1.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-2.jpg
2x 12" Clarion SW1251 350W RMS subs $69 each
Specifications:
Speaker Size: 12" (30cm)
Power Handling: 700W Peak, 350W RMS
Voice Coil: 4-Ohm SVC (Single Voice Coil)
Magnet: Dual Strontium Ferrite
Terminals: Gold Plated
Cone: Fiberglass/Paper design
RRP: $129.99
Because everyone loves 12" subs - ideal boot shakers, great all-round sound, highly recommended in a pair.
http://eclipsecomputers.co.nz/temp_i...ion-SW1251.jpg
4x 12" Clarion PXW1252 500W RMS subs $130 each
Specifications:
Speaker Size: 12" (30cm)
Power Handling: 1000W Peak, 500W RMS
Voice Coil: 4-Ohm DVC (Dual Voice Coil)
Magnet: Dual Strontium Ferrite
Terminals: Gold Plated
Cone: Kevlar/Paper design
RRP: $389.99
For more powerful 12" subs - which everyone loves. Dual voice coils mean running two of these together in parallel gives you a 1Ohm load - ideal for monoblocks (such as the 1KW amp I'm selling also hint hint...). Four of these in one car would be mad!
http://eclipsecomputers.co.nz/temp_i...nPXW1252-0.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-1.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-2.jpg
1x 15" Clarion PXW1552 750W RMS $160
Specifications:
Speaker Size: 15" (39.5cm)
Power Handling: 1500W Peak, 750W RMS
Voice Coil: 4-Ohm DVC (Dual Voice Coil)
Magnet: Dual Strontium Ferrite
Terminals: Gold Plated
Cone: Kevlar/Paper design
RRP: $499.99
For lovers of deep, hard hitting, long bass hits when 12" subs just don't cut it. Dual voice coils let you load up your favourite amp (see the Soundstream on sale at the top of the thread, that pumps 800W RMS @ 2Ohms - ideal!).
http://eclipsecomputers.co.nz/temp_i...nPXW1252-0.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-1.jpg
http://eclipsecomputers.co.nz/temp_i...nPXW1252-2.jpg
Intercooler:
Top-Mount style Intercooler for TD04-15T $30
Factory Intercooler, was used in top-mount set up (top-mounting attachments not included).
Some bent fins on top, but no leaks and works well - designed for use with TD04-15T in RVR X3 factory set up, but good for use with any turbo up to this size (and maybe bigger if you front-mount it).
http://eclipsecomputers.co.nz/temp_i...pMountIC-0.jpg
http://eclipsecomputers.co.nz/temp_i...pMountIC-1.jpg
http://eclipsecomputers.co.nz/temp_i...pMountIC-2.jpg
http://eclipsecomputers.co.nz/temp_i...pMountIC-3.jpg
Turbo:
EVO I TD05-16G Housings, Internal Wastegate, factory oxygen sensor $100ono
EVO I TD05-16G genuine exhaust housing (cracked through to internal wastegate, needs welding up for maximum flow/boost control), factory TD05-16G compressor cover and Internal Wastegate to suit. Factory oxygen sensor still attached to exhaust housing. Ideal to mate up to EVO I - III exhaust manifold flange. Turbine (compressor wheel and exhaust) have been removed for use in my new turbo. Bought this for $450+GST, hope someone gets good use out of the parts remaining Pictures to go up later.
Rain/Wind deflectors to suit RVR/SUV:
Aftermarket Rain/Wind deflectors off RVR $20
Pair of wind-deflectors to suit RVR or other SUV/Van.
Good condition, no cracks, no major scratches, comes with all mounting points.
Have just checked with another potential buyer, do not fit Mitsubishi L200 (Ute).
http://eclipsecomputers.co.nz/temp_i...dsheilds-0.jpg