MarkSanne
19-01-2010, 08:49 PM
Well, today's the day that I finally took the time to get the ECU out of Legnum to make sure it has the 7202 'flashable' ECU. And it does!
uploaded/1887/1263929819.jpg
uploaded/1887/1263929835.jpg
uploaded/1887/1263929847.jpg
And this is where the fun should have continued, but when I connected the laptop to the ODB using a tactrix 1.3 (not sure if 1.3 or 1.3U) the ECUflash program (version 1.42.2595) can't connect to the ECU. I've tried the first 3 options ECUflash displays:
1996-2001 Mistubishi 2nd Gen/EVO5-6
1996-2001 Mitsubishi 2nd Gen/EVO6.5 MH7203F
2001-2005 Mitsubishi 3rd Gen/EVO7-8
This is what I get back:
[20:27:59.208] Using interface OpenPort 1.3 Universal TX29Cjha6dcdf6d5472695dcb84da285ba5b5a82cf3831c7
[20:28:01.989] sending init sequence 2
[20:28:01.989] got 0x11 response
[20:28:01.989] sending init sequence 3
[20:28:02.380] entering bootloader
[20:28:02.395] sending kernel size (2029)
[20:28:02.395] sending kernel load address (0x0000F000)
[20:28:02.427] uploading kernel
[20:28:02.755] verifying kernel checksum response
[20:28:02.755] kernel valid
[20:28:02.958] kernel get version
[20:28:02.989] kernel version is : OpenEcu Mitsubishi H8/539F Kernel V1.06
[20:28:02.989] reading kernel comm buffer size
[20:28:02.989] comm buffer size set to 256
[20:28:02.989] reading kernel flash buffer size
[20:28:03.005] flash buffer size set to 1024
[20:28:03.020] interface close
Any ideas anyone? I'm probably doing something stupidly wrong, but I just can't see what.
uploaded/1887/1263929819.jpg
uploaded/1887/1263929835.jpg
uploaded/1887/1263929847.jpg
And this is where the fun should have continued, but when I connected the laptop to the ODB using a tactrix 1.3 (not sure if 1.3 or 1.3U) the ECUflash program (version 1.42.2595) can't connect to the ECU. I've tried the first 3 options ECUflash displays:
1996-2001 Mistubishi 2nd Gen/EVO5-6
1996-2001 Mitsubishi 2nd Gen/EVO6.5 MH7203F
2001-2005 Mitsubishi 3rd Gen/EVO7-8
This is what I get back:
[20:27:59.208] Using interface OpenPort 1.3 Universal TX29Cjha6dcdf6d5472695dcb84da285ba5b5a82cf3831c7
[20:28:01.989] sending init sequence 2
[20:28:01.989] got 0x11 response
[20:28:01.989] sending init sequence 3
[20:28:02.380] entering bootloader
[20:28:02.395] sending kernel size (2029)
[20:28:02.395] sending kernel load address (0x0000F000)
[20:28:02.427] uploading kernel
[20:28:02.755] verifying kernel checksum response
[20:28:02.755] kernel valid
[20:28:02.958] kernel get version
[20:28:02.989] kernel version is : OpenEcu Mitsubishi H8/539F Kernel V1.06
[20:28:02.989] reading kernel comm buffer size
[20:28:02.989] comm buffer size set to 256
[20:28:02.989] reading kernel flash buffer size
[20:28:03.005] flash buffer size set to 1024
[20:28:03.020] interface close
Any ideas anyone? I'm probably doing something stupidly wrong, but I just can't see what.