View Full Version : Finally decided to do something
Badger_01
21-09-2012, 02:14 AM
So after taking the Legnum up the road and losing power and it turning off :uhoh:
I realised that it was the throttle body elbow as it has popped off a few times before.
So a quick fix and slowly went back home.
Took the elbow off and this is what I find:
O ring thing is well.. The picture explains it :quasi:
57788
Elbow looks interesting too.
57789
And the clamp notches are a bit deformed
57790
So following Swinks's Guide (http://www.clubvr4.com/forum/showthread.php?50728-Hard-pipe-kit-DIY-guide&p=567473#post567473)
But instead of using 70 degree pipe I used a 45 degree pipe.
After trial and error, cutting bits off here and there it now fits :d
57791
Just got to do the vacuum outlets now :thumbsup:
scott.mohekey
21-09-2012, 02:26 AM
That looks good!
Badger_01
21-09-2012, 02:52 AM
Thanks Scott :)
I'll put up a pic once it's all finished :thumbsup:
CANDEE
21-09-2012, 04:57 AM
Make sure you keep the restrictor pill in the lines from the original pipe.... You can have boosting issues without it... ;)
Badger_01
21-09-2012, 05:12 AM
I love happy endings :D
Me too! :D
Make sure you keep the restrictor pill in the lines from the original pipe.... You can have boosting issues without it... ;)
Lol original pipe was never there, just a black one, so changed it to the red one
Wodjno
21-09-2012, 09:44 AM
Good Job /yes look forward to the end result :)
Wodj
SGHOM
21-09-2012, 11:07 AM
Good Job /yes look forward to the end result :)
Wodj
But a nice block of hardwood has the same result...ish :)
Wodjno
21-09-2012, 12:08 PM
The very one :D
Sent from my HTC Wildfire using Tapatalk 2
Badger_01
22-09-2012, 01:21 AM
Lol nice block of wood :P
Badger_01
22-09-2012, 02:39 AM
And done!
57799
Badger_01
24-09-2012, 12:49 AM
All hard piping is now done :D
57824
low_vr4
23-12-2013, 12:58 AM
Hey Reece, where did you buy the pipes from? Ebay?
Badger_01
23-12-2013, 07:01 AM
Nope, just from scarles on trademe
Bender
19-04-2014, 05:49 AM
Sorry to bring up an old thread
Reece, Did you use a 45 degree pipe for y-pipe to the intercooler or did you find a 70 degree pipe?
Also you did you get your mikalor style clamps from?
Cheers.
Badger_01
19-04-2014, 06:07 AM
Sorry to bring up an old thread
Reece, Did you use a 45 degree pipe for y-pipe to the intercooler or did you find a 70 degree pipe?
Also you did you get your mikalor style clamps from?
Cheers.
Ummmm I used 45 degree pipe, 2.75" and I got the clamps from Scarles in Auckland. But we sell the clamps at my work, so could get you a good price if you want?
It was a lot of trial and error, so under cutting the pipe instead of over cutting it lol
wintertidenz
19-04-2014, 06:33 AM
You can get away with 45 degree bends. If you're like me and had no air box to start with, you can just use a straight bit of pipe and make up a cold air box where the battery normally sits instead.
Bender
19-04-2014, 06:36 AM
Ummmm I used 45 degree pipe, 2.75" and I got the clamps from Scarles in Auckland. But we sell the clamps at my work, so could get you a good price if you want?
It was a lot of trial and error, so under cutting the pipe instead of over cutting it lol
If you can, It would be awesome...
Was reading Swinks thread, Going be alot of fun times ahead
Bender
19-04-2014, 06:37 AM
You can get away with 45 degree bends. If you're like me and had no air box to start with, you can just use a straight bit of pipe and make up a cold air box where the battery normally sits instead.
Might do that down the line but will just do that part with 45 degree pipe for now
wintertidenz
19-04-2014, 06:40 AM
If it's easier you can also go for 3" and then use a 3" to 2.75" 90 degree silicone joiner.
Bender
19-04-2014, 06:49 AM
So using a 3" pipe would be better in the long run?
wintertidenz
19-04-2014, 08:04 AM
It depends if you are looking at bigger power later on. I only went 3" post-intercooler because I was looking at doing the TD04 upgrade down the track, and I had spare 3" piping/silicone lying around.
3" pipe should be easier to find though.
Bender
19-04-2014, 08:13 AM
I won't be looking for big power, I have found everything on trademe I need but from the clamps
Badger_01
19-04-2014, 08:35 AM
If you can, It would be awesome...
Was reading Swinks thread, Going be alot of fun times ahead
Yep will do, just give me a yell with how many you need and what size
Bender
19-04-2014, 08:45 AM
Yep will do, just give me a yell with how many you need and what size
Total of 12 are needed :)
3x 67mm to 75mm
4x 54mm to 64mm
5x 73mm to 81mm
Badger_01
19-04-2014, 10:37 AM
Total of 12 are needed :)
3x 67mm to 75mm
4x 54mm to 64mm
5x 73mm to 81mm
Sweet as, I'll get back to you on Tuesday with a price
Powered by vBulletin® Version 4.2.0 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.