Tab Content
Davezj's Activity
Visitor Messages
About Me
My Vehicles
Tab Content
  • Davezj's Avatar
    Yesterday, 11:43 AM
    are you looking for COTY door cards or UK spec galant Leather door card with the white stitching. it might be good for people to know.
    6 replies | 181 view(s)
  • Davezj's Avatar
    09-06-2021, 11:20 PM
    Davezj replied to a thread Down pipe in General / Questions
    lots of heat and penetrating oil before you try and remove bolts will see you right.
    4 replies | 126 view(s)
  • Davezj's Avatar
    09-06-2021, 11:17 PM
    bloody hell don that is one hell of a circumstance. hope you feel better sooner rather than later.
    9 replies | 240 view(s)
  • Davezj's Avatar
    09-06-2021, 11:13 PM
    hmm that is interesting as my next engine build will be wanting to fit forged pistons and rods. but this will mean cylinder board machining to oversized pistons and posibly crank bore/journals resized as the standard bearing seem to be getting difficult to get hold of.
    4 replies | 179 view(s)
  • Davezj's Avatar
    09-06-2021, 11:05 PM
    looks like a bad engagement of the starter cog teeth as nev has said. looks like only partial contact on start up. it is a gerbox out of the car job to change the torque plate, as it is bolted to the end of the crankshaft. the torque plate clattering against the torque converter bolts will probably have damage the holes in the torque plate and elongated them. remember to use thread lock on the crankshaft bolts as well as the torque converter bolt. if you dont use thread lock in the...
    10 replies | 122 view(s)
  • foxdie's Avatar
    08-06-2021, 01:38 PM
    Hi Don, I'm not immediately interested in any of these things (perhaps the donor shell) but I just wanted to extend sympathy for what's happened to you. If you need someone to talk to, you know we are here! Ps. Do you have WhatsApp? We have a group chat there you are more than welcome to join, here's the invite link; Kind regards, Jay
    9 replies | 240 view(s)
  • Davezj's Avatar
    05-06-2021, 12:54 PM
    what is exactly wrong with you torque converter. please explain a little bit more and we might be able to help "shuttering with starter motor" tells us nothing i had an issue with my torque converter (T/C) on start up and on idle, and lift off of the accelerator. i had a random clattering noise. the flex plate to torque converter bolts had worked loose and were rattling in the flex plate holes.
    10 replies | 122 view(s)
  • Davezj's Avatar
    03-06-2021, 11:32 PM
    I added my name in WhatsApp chat. But I will say yes I am in on here as well.
    8 replies | 191 view(s)
  • Davezj's Avatar
    31-05-2021, 10:47 AM
    Hi Tim, Do you have the plastic trim panel from under the steering wheel. And the engine cover. How much do you want for them. Ping me a pm.
    18 replies | 361 view(s)
  • Davezj's Avatar
    31-05-2021, 10:43 AM
    I changed the idle point in the ECU . Because as standard the idle out of gear. Is different to the idle in gear value. One is set to 600rpm and one is set to 650rpm. I think it is the in gear idle set to 600rpm which was to low on my car. Setting it to 650rpm was good for me. I changed it because 600rpm set up a resonant frequency vibration in my car and I wanted to get rid of that.
    11 replies | 160 view(s)
  • Davezj's Avatar
    26-05-2021, 11:29 PM
    Hi And welcome to the club. everyone is welcome here. full membership is is a good idea. you get to all the extra stuff in the library, and it is only £10 a year. well worth it. plus you get discounts from most people sell stuff on here.
    11 replies | 188 view(s)
No More Results

8 Visitor Messages

  1. View Conversation
    Hi DaveZj,
    I have AYC error codes:
    31, 81and 82.
    I guess that its some wire which is broken.
    Do you have any idea where i can find this wires?
    Best regards
    Ps my car is VR4, AUTOMATIC 2.5 1999, 4WD, 280HP SALOON
  2. View Conversation
    Do you know if this set is still the one for the 6a13tt?
    Wanna order 2 sets of them.
  3. View Conversation
    Hi there I have bought a fuel pressure regulator and not sure how to plumb it in really do you have any information please
  4. View Conversation
    Hi there spoke to you before with few issues with my 1996 legnum.well at the moment it running fine touch wood just want to no any contacts that could. Remap mine and hopefully have a newer ecu as mine is 7201, have spoke to Jason about remapping and other ecu to fit but for some reason won't get back to me hope you can help

    Many thanks
  5. View Conversation
    Pm me your address Dave
  6. View Conversation
    hello mate any luck with postage
  7. View Conversation
    hi Dave can you give my souraund for enyone who go to Guilford RR day please.
  8. View Conversation
    Hey Dave,

    Ecu came the other day, but it wasn't in good condition... it was in awesome condition! Anyway thanks so much for being so generous again. Can you remember if it was from a manual or an auto?

Showing Visitor Messages 1 to 8 of 8
About Davezj

Basic Information

About Davezj
Membership Number:
playing with VR-4
Mass Spectrometer/Electronics PCB Design Engineer
First Name:


Bye for Now!


Total Posts
Total Posts
Posts Per Day
Visitor Messages
Total Messages
Most Recent Message
21-05-2020 05:47 PM
General Information
Last Activity
Today 12:33 AM
Join Date

6 Friends

  1. dodo_ireland 

    Registered User

  2. foxdie 

  3. Humpty's Revenge 

    Humpty's Revenge
  4. pixelplay 

    Registered User

  5. vr4drifta 

    Registered User

  6. VR4Kaos 

Showing Friends 1 to 6 of 6