Tab Content
Humpty's Revenge's Activity
About Me
My Vehicles
Media
  • Davezj's Avatar
    16-04-2024, 08:58 PM
    Davezj replied to a thread BLUE PRINT ADC48233 Wheel bearing kit for MITSUBISHI GALANT in UK Parts for Sale / Wanted
    the link is not for a wheel bearing kit.
    see more
    1 replies | 35 view(s)
  • Davezj's Avatar
    16-04-2024, 08:49 PM
    Davezj replied to a thread Anyone Still Around? in UK Chat
    i am still here somewhere, but i can't find me at the moment, i am probably in the back of one of my sheds.
    see more
    7 replies | 128 view(s)
  • Davezj's Avatar
    15-04-2024, 09:46 PM
    Davezj replied to a thread Performance Mod clear out in UK Parts for Sale / Wanted
    Hi there, I will take rods if they fit the vr4 engine without modification. Do you have a bearing size spec to fit them. Drop me a pm and we can arrange payment and delivery.
    see more
    2 replies | 87 view(s)
  • Nick Mann's Avatar
    05-04-2024, 08:26 AM
    Nick Mann replied to a thread 6A13 N/A rattle noise from engine bay at high rpm in Engine
    Good luck! :thumbsup:
    see more
    4 replies | 107 view(s)
  • foxdie's Avatar
    04-04-2024, 10:34 AM
    foxdie replied to a thread Hello from England in Newbies Area
    Welcome Shao, where about's in the UK are you based? Most of us are dotted around :)
    see more
    6 replies | 105 view(s)
  • Nick Mann's Avatar
    04-04-2024, 10:33 AM
    Nick Mann replied to a thread 6A13 N/A rattle noise from engine bay at high rpm in Engine
    You are asking some interesting questions there, but I'm not sure any of us have the experience to answer them! My guess would be that the bolt pattern on the gearbox and the mounting points will be key. In some cars the TCU and the ECU are combined - I'm not sure about your car or the donor car, but that might also confuse the issues of installation?
    see more
    4 replies | 107 view(s)
  • foxdie's Avatar
    04-04-2024, 10:32 AM
    foxdie replied to a thread New Member in Newbies Area
    Welcome /Wave
    see more
    4 replies | 47 view(s)
  • foxdie's Avatar
    04-04-2024, 10:26 AM
    foxdie replied to a thread Does anyone recognise that in Gearbox / Transmission
    Happy to help where required, I can perform the following dash programming services (Hi-vis VR-4 dash clusters only!); Adjust the scaling of the gearbox signal This changes what speed the dash sees, exactly what a speedo converter does. Odometer and trip values are left the same, but the speedometer and how much the odometer and trip counters increment is then changed to MPH or KPH. Adjust the needle scaling For those who want to fit a 240, 260 or a 280 dash fascia, this just adjusts...
    see more
    10 replies | 19286 view(s)
  • Nick Mann's Avatar
    04-04-2024, 09:15 AM
    Nick Mann replied to a thread Back in a vr4 in General Chat
    I'd agree with Nev - missfires are often coil packs now, but start with the easy/cheap basics! Good luck.
    see more
    13 replies | 215 view(s)
  • Nick Mann's Avatar
    04-04-2024, 09:13 AM
    Nick Mann replied to a thread New Member in Newbies Area
    /Welcome Where are you based? Any more details on the car? Oh, and we love pictures on here!
    see more
    4 replies | 47 view(s)
  • Nick Mann's Avatar
    04-04-2024, 09:12 AM
    Nick Mann replied to a thread Does anyone recognise that in Gearbox / Transmission
    As Garry says - if the converter is on the gearbox you need to go downwards from the throttle body area to find the sensor/plug/loom on the top of the gearbox. The one in the photo you referred to is definitely one that plugs in to the top of the gearbox. If you find it then I'd thoroughly recommend removing it so the car reads in km/h again then see Jay foxdie to reprogramme your speedo.
    see more
    10 replies | 19286 view(s)
  • elnevio's Avatar
    02-04-2024, 05:38 PM
    elnevio replied to a thread Hello from England in Newbies Area
    /Welcome Also echo the other comments about having more pics /Camera and checking/treating for rust :2thumbsup
    see more
    6 replies | 105 view(s)
  • elnevio's Avatar
    02-04-2024, 05:36 PM
    elnevio replied to a thread Back in a vr4 in General Chat
    Nice to see pics, even sideways ones!! :D Always worth changing plugs anyway, especially if the service history is a little unknown. Misfires on these tend to be failing coilpacks as the originals are all getting ancient and are all subject to a lot of heat; but see how the plug/lead change does for now.
    see more
    13 replies | 215 view(s)
  • elnevio's Avatar
    02-04-2024, 05:03 PM
    elnevio replied to a thread Anyone Still Around? in UK Chat
    Still here! But very rubbish at catching up on here - even my signature is well out of date!!! /pan
    see more
    7 replies | 128 view(s)
  • foxdie's Avatar
    01-04-2024, 10:36 PM
    foxdie replied to a thread Anyone Still Around? in UK Chat
    Still alive, still in a VR-4 ;)
    see more
    7 replies | 128 view(s)
  • Nick Mann's Avatar
    29-03-2024, 04:44 PM
    Nick Mann replied to a thread Hello from England in Newbies Area
    Have fun! Check for rust and treat ASAP would be my only initial advice! Hope you continue to grin. :thumbsup:
    see more
    6 replies | 105 view(s)
  • Nick Mann's Avatar
    29-03-2024, 04:43 PM
    Nick Mann replied to a thread Anyone Still Around? in UK Chat
    I'm still here. But yes, it's a bit quiet on here compared to 15 years ago! Good luck in your search ;)
    see more
    7 replies | 128 view(s)
  • Nick Mann's Avatar
    29-03-2024, 04:42 PM
    Nick Mann replied to a thread Back in a vr4 in General Chat
    You don't want the plug gaps to be 1.1 in the VR4. Those sound like N/A V6 plugs. You should consider the flashy dash method of code reading - it's generally much more reliable than code readers - the VR4 is not ODB2 compliant and often code readers tell porkies as they interpret the codes incorrectly. Glad things are progressing though!
    see more
    13 replies | 215 view(s)
No More Results

Statistics


Total Posts
Total Posts
9,601
Posts Per Day
1.58
General Information
Join Date
09-09-2007
Referrals
0
Add your vehicle to the garage