Replacements, aftermarket and parts from other vehicles that fit

I will try and fill this post with as much info as possible, I'm new to vr4's my experience is very minimal but I'll try my best, not quite sure how this should be laid out regards

Parts that definitely fit with no modifications needed and

Parts that fit with modifications? This section would seem pointless because almost anything will fit with modifications, so I think sticking with straight swap is the best route and maybe a section with DIY,able mods like coil over plug is relatively easy to do with little mechanical knowledge.

BUSHES

energy*suspension do a kit for the AWD*eclipse*1999 which fits the VR4.

enerysuspensionparts.com in the USA are a distributer, if i remeber correctly it will cost about £120 for the kit, Unathane inserts for the front and rear suspension arms and shock top mounts and manual gear shift bushes.

Link for kit is below

https://www.energysuspensionparts.com/5.18107

BRAKES

evo 4 -9 calipers fit straight on to facelift models along with the disks and pads,

Pre face lift. . . . . ?

Standard calipers with aftermarket good quality pads and disks make a huge improvement and maybe all you need and sometimes can work better as with bigger brake conversions extra rotating weight and the weight of the calipers can affect the characteristics of the car

AYC PUMP
Ayc pumps fit from evo 4 - 9, people have fitted SAYC but I'm not up to speed as to what is involved again if anyone can confirm I will edit and keep it straight to the point




REAR DIFFERENTIAL
So far I believe the diffs from evo 4 -9 fit but the evo 8 diff bolts straight in, can anyone confirm this info and I'll edit this section


COIL PACKS


WHEELS

Tyre size calculator to make sure your speedo stays as acurate as possible...

http://www.miata.net/garage/tirecalc.html,

18" x 8.5" rim 35 offset, with a 225/40/18 tyre will fit on a lowered car with no problems.

if the camber fix/mod is done, the rear guards need to be rolled,

17" x 7" rim 40 offset, with a 215/40/17 will fit with no issues at all,

18" x 8" rim 38 offset, with a 225/40/18 tyre will fit on a lowered car with no problems.

if the camber fix/mod is done, the rear guards need to be rolled,


SUSPENSION

Rear camber bolt kit from viamoto

https://www.viamoto.co.uk/proddetail...+VR4+EC5W+EC5A
Attachment 81168

There is a good amount of suspension struts available as well as coilovers from Tein and BC Racing etc.

Cusco sway bars are available at RHD JAPAN link below to rear arb but they stock the front as well as lots of other items.

https://www.rhdjapan.com/cusco-rear-sway-stabilizer-bar-ec3w-ec5w.html

BOOT GAS STRUTS


ECU
Link g4+ supplied by euro spec amongst other companies but preferred by the vr4 community.

EXHAUST
BM Catalysts in Mansfield supply down pipes.

DRIVETRAIN
Febest make CV and trilobe joints for the front driveshafts

DASH FLASHY LIGHTS DIAGNOSTICS
Below is a link to Confused's dash flashing lights diagnostics

https://www.clubvr4.com/forum/showth...agnostic-Codes

body panels
???????
Sills in link below
https://www.ebay.co.uk/itm/HQ-MITSUB...AAAOSwql1c0Zi9

https://www.klokkerholm.com/xProduct...x?Group=142924
(also has saloon listed)
Sills have same part no for all cars, saloon and estate, from 2.0 to VR4

ENGINE
Perrin 3 port electronic boost control valve
https://frsport.com/perrin-performan...0aAnlZEALw_wcB

Stepper motor to control idle
https://rover.ebay.com/rover/0/0/0?m...2F282776664035

BM catalysts in Mansfield do downpipes.

Febest make CV and trilobe joints for the front driveshafts.

Does anyone have anything to add to this? Any links? Or known mods, replacements or suppliers?

Bump

More info added to the list

I came across this following a russian repair video...

https://www.klokkerholm.com/xProduct...x?Group=142924
(also has saloon listed)
Sills have same part no for all cars, saloon and estate, from 2.0 to VR4.

Maybe those part number listings can lead to finding the panels for sale somewhere?

Thank you for that I will add it to the list, I'm at a dilemma with mine at the min, I don't know whether to buy the one on Ebay which is very clean and break mine or stick with repairing mine but fear the rust will always come back?