ecuflash .bin file (need xml)

would any of you clever chaps like to take a look at this FTO ecu rom and see if you can come up with an xml for it please.

I think Ive found the fuel and ignition maps.. but the axis are wrong

Attachment 45167Attachment 45168
Attachment 45165Attachment 45166

<table name="Fuel Map 1 - HI OCTANE " category="Fuel and Ignition Maps" address="1182B" type="3D" swapxy="true" scaling="AFR">
<table name="Load" address="2eb42" type="X Axis" elements="8" scaling="Load"/>
<table name="RPM" address="2ec62" type="Y Axis" elements="17" scaling="RPM"/>
</table>

<table name="Fuel Map 2 - LO OCTANE " category="Fuel and Ignition Maps" address="118BB" type="3D" swapxy="true" scaling="AFR">
<table name="Load" address="2eb42" type="X Axis" elements="8" scaling="Load"/>
<table name="RPM" address="2ec62" type="Y Axis" elements="17" scaling="RPM"/>
</table>

<table name="Ignition Map 1 - HI OCTANE " category="Timing" address="11c07" type="3D" swapxy="true" scaling="Timing">
<table name="Load" address="2eb42" type="X Axis" elements="9" scaling="Load"/>
<table name="RPM" address="2cf9a" type="Y Axis" elements="21" scaling="RPM"/>
</table>



<table name="Ignition Map 2 - LO OCTANE " category="Timing" address="11ccb" type="3D" swapxy="true" scaling="Timing">
<table name="Load" address="2eb42" type="X Axis" elements="9" scaling="Load"/>
<table name="RPM" address="2cf9a" type="Y Axis" elements="21" scaling="RPM"/>
</table>

fuel:
RPM: 2c430
Load: 2c458

Ignition:
RPM: 2c490
Load: 2c4ce

All care and no responsibility.... I didn't verify in EcuFlash but it looks right in disassembly.

fuel:
RPM: 2c430
Load: 2c458

Ignition:
RPM: 2c490
Load: 2c4ce

They look spot on - thanks.

Any joy with the revlimit?

Try 10882 for rev limit. A bit different to the VR-4 code, so not 100% on that one.

thats what we had for the rev limit, I think there must be 2, as thats 6209rpm which I think is what the limit is set to before the car warms up. There should be one around 8050rpm.

I would hazard a guess at 8117 being the RPM limit you are after ;)

<table name="Rev LimitA" category="Limits" address="10882" type="1D" level="4" scaling="RPMLimit_16bit"/>
<table name="Rev LimitB" category="Limits" address="113fa" type="1D" level="4" scaling="RPMLimit_16bit"/>

looks good, thanks, any luck with the injector sizes? and there should be a mivec point in there somewhere, then I think weve got everything we need.

How were you able to read the rom? I have tried on some FTO's and wasn't able to. If you could let me know how you did it please as I have a lot of WA Customers who would love this as an option for tuning.

plugged in the openport 2.0 then wired the white re-flash connector in to pin 79 on the ECU and it allowed me to read it.

Okay thanks so to confirm, in my understanding (Lol) you hooked up the OP2.0 but you wired back to the ECU pin 79 for teh K line voltage input into the back of the OP2.0 plug. Have you confirmed you can write back to it yet?

thats correct we haven't confirmed we can write back yet, but its the 7202 chip in same as the VR4 so it should be writeable. I will try it sometime this week.

I remapped an FTO yesterday and disconnected the battery for an hour and it retained its new settings so it works :)