Page 1 of 7 123 ... LastLast
Results 1 to 20 of 129

Thread: Dyno 19T HL +AEM EMS+E85 Manual galant VR4 ..We need to talk ..loool..

  1. #1

    Offline
     
    Name
    Saphir
    Join Date
    Mar 2011
    Last Online
    12-03-2024
    Posts
    321
    Country
    Other
    Location
    Mulhouse/France
    Car
    3000GT VR4/
     

    Talking Dyno 19T HL +AEM EMS+E85 Manual galant VR4 ..We need to talk ..loool..

    Hi all ,

    I made Ã* dyno today with my car .. This is my setup:

    -Galant VR4 manual ( 5 speed)
    -TD04 19T HL
    -E85
    -RC 1000 injectors
    -AEM EMS From 3000GT with custom harnais
    -Fmic 76mm
    -HKS SSQV
    -Aeromotive stealth 340 ( not hotwired yet)
    -Resistor pack from 3000GT
    -Custom exhaust
    -IK24 plug
    -Stock coils ( 15 years)
    -Magnecor lead
    -AEM Wideband
    -Speed density ( No MAF!!! ) With win apexi filters
    -Aem map sensor 3.5 bars + IAT
    -etc etc etc ...

    Please note: Stock cams , stock cams gear , stock heads and valves , Tip on the exhaust muffler , no EBC ( my ebc is fail) i have vaccum hose WG to plenum , BOOST was 0.75bars

    This is the Dyno 297awhp and 401nm:

    733954_582873011723024_2063701927_n.jpg

    Saf
    3000GT 1430awhp and 1132nm twin 6466CEA @ 44 psi + Galant VR4 type-S 701awhp @ 1.7 bars 6466CEA + Galant GDI to 4G63 ... In progress

  2. #2

    Offline
     
    Name
    Saphir
    Join Date
    Mar 2011
    Last Online
    12-03-2024
    Posts
    321
    Country
    Other
    Location
    Mulhouse/France
    Car
    3000GT VR4/
     
    I'll make an other dyno tomorow without the tip on the muffler , i think that i can take 10awhp...

    I ordered a coils and ptu for 3000GT , to install on the galant VR4 ... Now it's impossible to check the timing with a timing light and i don't know how much timing i have ... On the aem ems , we need to sync the timing ... i made my ignition map with 22° to the redline @ 0.75 bar range ( for an exemple ) but i can have 16° of timing or 14° or 12°...it's hard for me to explain in English , because i'm french ..

    Also , i think that the camshaft profil is not designed to have power at the top end ... See the dyno ... I already made a measurement of the intake and exhaust valve and comming soon the flow bench for a vr4 heads.

    Saf

    Ps: Ignition Sync :

    The ignition sync is there just to be sure that the EMS is displaying the correct amount of degrees before or after TDC the engine is actually receiving. For example, say that you give the engine 16* of timing at idle on the ignition map, so you set the active idle cells on the ignition map to 16*. But how do you know if the EMS is ACTUALLY giving it 16*? Maybe it's 18*...maybe it's 26*...? Unless the ignition is synced with the EMS, there is no way to know. This is obviously why the actual timing and the EMS timing need to be synced. To do this all you need is a timing light and a crank pulley with some markings on it. Once you find the timing marks on the crank pulley, you can hook up the timing light. You're then going to want to lock the ignition timing so it doesn't move at all.
    Last edited by SAF68; 13-03-2013 at 07:43 PM.

  3. #3

    Offline
     
    Name
    Saphir
    Join Date
    Mar 2011
    Last Online
    12-03-2024
    Posts
    321
    Country
    Other
    Location
    Mulhouse/France
    Car
    3000GT VR4/
     
    Reserved , thank's

    Saf

  4. #4
    Davezj's Avatar

    Offline
     
    Name
    Dave
    Join Date
    Jan 2006
    Last Online
    09-01-2024
    Membership ID
    255
    Posts
    16,245
    Country
    England
    Location
    Manchester
    Car
    VR-4
    My Garage
    Visit
     
    what are trying to say, are you saying this is good or are you saying this is bad.

    Bye for Now!

  5. #5
    swinks's Avatar

    Offline
     
    Name
    Tomasz
    Join Date
    Feb 2008
    Last Online
    21-10-2022
    Posts
    4,578
    Country
    United Kingdom
    Location
    Bourne, Lincs.
    Car
    ex-Galant VR4
     
    Quote Originally Posted by Davezj View Post
    what are trying to say, are you saying this is good or are you saying this is bad.
    Read the dyno graph and description of setup, and you will see clear
    Ex: Galant VR4
    Running 268 HP ATW and 443 Nm torque at 0.9 bar
    Now: Lancer Evolution 8 FQ-300
    Running 325 HP ATW and 510 Nm torque at 1.6 bar

  6. #6

    Offline
     
    Name
    Saphir
    Join Date
    Mar 2011
    Last Online
    12-03-2024
    Posts
    321
    Country
    Other
    Location
    Mulhouse/France
    Car
    3000GT VR4/
     
    Quote Originally Posted by Davezj View Post
    what are trying to say, are you saying this is good or are you saying this is bad.
    For 0.75 bar , it's good !!! but we can see after 6000rpm the power drop !! The stock cams are not made for big turbos or for top ends ... The igniction coils are not ok for 330awhp and more .... The stock coils can't received the HKS DLI and that is why i'll go with the stock 3000GT ignition ... Anyway , with 0.75 bars we are not on the good range for the 19T ... i'll post an other dyno with the new coils , same boost boost and ignition synced

    Saf

  7. #7
    Davezj's Avatar

    Offline
     
    Name
    Dave
    Join Date
    Jan 2006
    Last Online
    09-01-2024
    Membership ID
    255
    Posts
    16,245
    Country
    England
    Location
    Manchester
    Car
    VR-4
    My Garage
    Visit
     
    is he just boasting, he has td04 so i would expect it to make more power at lower boost levels, he also has big injectors and upgrade fuel pump, etc, etc.
    only the first post was populated when i asked the questions.

    he has posted again i the time it has take for my to type my response.

    ok so he is happy with the result. good for you Saf

    you already have a VR4 with 423atw bhp and that is a work in progress, well it says that in the signature.

    sound like you need to get and EBC plumbed in and hell will break loose!
    Last edited by Davezj; 13-03-2013 at 08:10 PM.

  8. #8

    Offline
     
    Name
    Saphir
    Join Date
    Mar 2011
    Last Online
    12-03-2024
    Posts
    321
    Country
    Other
    Location
    Mulhouse/France
    Car
    3000GT VR4/
     
    Quote Originally Posted by Davezj View Post
    is he just boasting, he has td04 so i would expect it to make more power at lower boost levels, he also has big injectors and upgrade fuel pump, etc, etc.
    only the first post was populated when i asked the questions.

    he has posted again i the time it has take for my to type my response.

    ok so he is happy with the result. good for you Saf

    you already have a VR4 with 423atw bhp and that is a work in progress, well it says that in the signature.

    sound like you need to get and EBC plumbed in and hell will break loose!
    Davezj , i made 423awhp , but with a lot off missfire ... With this topic and my feedback , i hope to help the owner to go on the right way , good gombo parts and i'm think that i'm not alone with TD04 turbos .... I saw many thread on this board and ozVR4 , but with times i saw that many peoples are lost on how to upgrade the car ... Ben from Eurospec is a nice guy ( 3/S owner ..loool) ...

    I saw a thread for camshaft for sale , but anybody know how is the stock cams , anybody tried cams gear for the overlap etc etc ..

    Saf

  9. #9
    swinks's Avatar

    Offline
     
    Name
    Tomasz
    Join Date
    Feb 2008
    Last Online
    21-10-2022
    Posts
    4,578
    Country
    United Kingdom
    Location
    Bourne, Lincs.
    Car
    ex-Galant VR4
     
    Quote Originally Posted by Davezj View Post
    is he just boasting, he has td04 so i would expect it to make more power at lower boost levels, he also has big injectors and upgrade fuel pump, etc, etc.
    Nope, you wouldn't.
    Search for TD04-19T flow chart and you will see that is a good solid result for such low pressure on this turbo. IIRC it's a wastegate openning pressure.

  10. #10
    Davezj's Avatar

    Offline
     
    Name
    Dave
    Join Date
    Jan 2006
    Last Online
    09-01-2024
    Membership ID
    255
    Posts
    16,245
    Country
    England
    Location
    Manchester
    Car
    VR-4
    My Garage
    Visit
     
    Saf, sounds like you are well on the way to making a big difference.

    repeat quote,
    "sound like you need to get and EBC plumbed in and hell will break loose!"

  11. #11
    Davezj's Avatar

    Offline
     
    Name
    Dave
    Join Date
    Jan 2006
    Last Online
    09-01-2024
    Membership ID
    255
    Posts
    16,245
    Country
    England
    Location
    Manchester
    Car
    VR-4
    My Garage
    Visit
     
    i think in the UK there might be 2 or 3 people on here with TD04 currently, there is Kyton and ???? and ?????.

  12. #12
    swinks's Avatar

    Offline
     
    Name
    Tomasz
    Join Date
    Feb 2008
    Last Online
    21-10-2022
    Posts
    4,578
    Country
    United Kingdom
    Location
    Bourne, Lincs.
    Car
    ex-Galant VR4
     
    Quote Originally Posted by Davezj View Post
    repeat quote,
    "sound like you need to get and EBC plumbed in and hell will break loose!"
    If tuning was a such easy and trivial matter as quoted everyone would run 500+ bhp vr4 now

  13. #13
    Davezj's Avatar

    Offline
     
    Name
    Dave
    Join Date
    Jan 2006
    Last Online
    09-01-2024
    Membership ID
    255
    Posts
    16,245
    Country
    England
    Location
    Manchester
    Car
    VR-4
    My Garage
    Visit
     
    ha ha, not meaning to make it sound easy, just a simplistic way of describing it.
    just a response to the lower boost setting that Saf has only useing wastegate pressure.
    he seems to every other base covered and yet probably the cheapest one to do is an EBC and he has not done it (well it is broken at the moment). and this would see some massive gains in his particular build as he says him self that this is the missing bit

    i am only just getting my head round using kenneths rom 1.03 for tuning my car. i want to understand what i doing before i jump in.
    i have all the bits in place that i want to do to my car at the moment, i have enough fuel, enough air, Spark is a little bit unkrown, i have AFR and Boost and Fuel pressure. so the next thing is the ECU.
    this is why i am interested in tweeking threads at te moment.

  14. #14
    horndog's Avatar

    Offline
     
    Name
    Marc
    Join Date
    Apr 2009
    Last Online
    05-09-2019
    Posts
    1,670
    Country
    United Kingdom
    Location
    Sheffield
    Car
    Saab 9-3 TurboX
     
    Quote Originally Posted by SAF68 View Post
    , but anybody know how is the stock cams
    http://www.clubvr4.com/forum/showthr...l=1#post664406
    It this the info you want?

    The specs for the OEM cams:
    Advertised duration 212/221
    duration@.050" -165/168
    lift -.200" /.205"

  15. #15

    Offline
     
    Name
    Saphir
    Join Date
    Mar 2011
    Last Online
    12-03-2024
    Posts
    321
    Country
    Other
    Location
    Mulhouse/France
    Car
    3000GT VR4/
     
    Quote Originally Posted by horndog View Post
    http://www.clubvr4.com/forum/showthr...l=1#post664406
    It this the info you want?

    The specs for the OEM cams:
    Advertised duration 212/221
    duration@.050" -165/168
    lift -.200" /.205"
    AWESOME !!! Thank's a lot Sir ... Very nice informations

    Please , correct me if i'm wrong but , i'm sure that : IS Not possible to have 500awhp with the OEM CAMS

    Advertised duration 212/221
    duration@.050" -165/168
    lift -.200" /.205"

    The stock 3000GT for an exemple ( and we know the oem 3000GT cams is not really good) is :

    Advertised duration 256/256
    duration@.050" -200/200
    lift -.349" /.350" ----> See the difference with the stock galant!!!!

    Nice find , thank's a lot ... i think that i'll go to regrind my camshaft for sure!

    Saf

  16. #16
    Davezj's Avatar

    Offline
     
    Name
    Dave
    Join Date
    Jan 2006
    Last Online
    09-01-2024
    Membership ID
    255
    Posts
    16,245
    Country
    England
    Location
    Manchester
    Car
    VR-4
    My Garage
    Visit
     
    here is the round 2 of the cam regrind thread, it will probably will mean much more to you than it does to me.

    http://www.clubvr4.com/forum/showthr...ht=kenneth%27s

  17. #17

    Offline
     
    Name
    Saphir
    Join Date
    Mar 2011
    Last Online
    12-03-2024
    Posts
    321
    Country
    Other
    Location
    Mulhouse/France
    Car
    3000GT VR4/
     
    Thank's a lot Sir for the link . Anyone know where we can find bigger valves ( intake and exhaust) ?

    Thank's

    Saf

  18. #18
    swinks's Avatar

    Offline
     
    Name
    Tomasz
    Join Date
    Feb 2008
    Last Online
    21-10-2022
    Posts
    4,578
    Country
    United Kingdom
    Location
    Bourne, Lincs.
    Car
    ex-Galant VR4
     
    Custom work Saf, unfortunately.

  19. #19
    Davezj's Avatar

    Offline
     
    Name
    Dave
    Join Date
    Jan 2006
    Last Online
    09-01-2024
    Membership ID
    255
    Posts
    16,245
    Country
    England
    Location
    Manchester
    Car
    VR-4
    My Garage
    Visit
     
    This thread might be a bit more helpful with regards to the cam regrind and valves
    http://www.clubvr4.com/forum/showthr...oi+cam+regrind

  20. #20

    Offline
     
    Name
    Christiandel
    Join Date
    Jun 2005
    Last Online
    13-11-2020
    Posts
    92
    Country
    Australia
    Location
    Brisbane
    Car
    96 Galant VR4
     
    Saf, does the 3000GT have the igniters built into the coils?

    pretty good effort on the 19T's

Page 1 of 7 123 ... LastLast

Similar Threads

  1. 3000GT AEM EMS on my galant VR4 ;)
    By SAF68 in forum ECUs / Mapping
    Replies: 12
    Last Post: 07-11-2012, 09:09 PM
  2. Td04-19t's
    By Oggie in forum Turbos, Exhaust & Induction
    Replies: 11
    Last Post: 06-03-2012, 10:24 AM
  3. Replies: 0
    Last Post: 04-02-2011, 03:16 PM
  4. Replies: 23
    Last Post: 14-06-2006, 09:18 PM
  5. Autronic SM2 or AEM EMS?
    By bradc in forum ECUs / Mapping
    Replies: 5
    Last Post: 13-11-2005, 04:51 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •