8g parts needed new or second hand must be good parts no cheap or bent stuff.

[billybobboot]

Ok need a few parts or were to find them
Need new or unbent front lower 4 point underbrace currently have cusco but its bent want a new one either cusco or rallyart but cant seam to find any.

Need new downpipes pref aftermarket as my front flexi has been hit and rubbed and put hole in. Again good condition or new no cheap ebay parts only want good quality no power flow ones.

also need lower brace that runs from front to back that runs under gearbox again new or second hand with no dents.

Money waiting.

[billybobboot]

Found a new front lower brace nengun do a cusco 4 point and cheaper 2 point so will order up a new 4 point as there only 85 odd which compared to 200 for one from auz land is a bit better for something thats the same + cusco is the same as on car at the mo. Next question is the vr4 subframe the better one being steel or is a non vr4 ally one better to go with? Im guessing vr4 but sometimes it can be other way round.

[Nick Mann]

My understanding is that the cast one is stiffer than the aluminium one.

Try Coordsport/Partbox for cusco stuff too.

[billybobboot]

They dont list the part but have asked.

[billybobboot]

Ok looks like i have found a new front under brace. Exhaust downpipes or front pipes got 3 options so waiting on replys

Last thing i really need is the engine brace that runs under the gearbox front to back if anyone braking one has one please let me know would normaly look myself but on holiday and only get signal in 2 places.

Stupid b roads in cornwall. Hit a hidden bump that after stopping would seam if your a local you know the hidden bump is there and they all stop and then go over it everyone elts just drives over and hits the underside of the car. Took out the front exhaust pipe the gearbox brace and my silly low subframe brace bent and then hit the exhaust and put a dent in just before second flexi only doing 30mph lucky wasnt light or may have been doing faster. Good thing is my wife chose the road so she said shes going to pay wooo.

[jkrzysztof80]

Is this what you want?
http://i987.photobucket.com/albums/a...412_124619.jpg

[TAR]

also need lower brace that runs from front to back that runs under gearbox again new or second hand with no dents.

I have a couple of these. I'll check if they are dented or not. I think you may be lucky to get a second hand one that hasn't at some time scraped on something.

[jkrzysztof80]

This one is mine if you want

[billybobboot]

Yer thats the one. Mine has taken a few too many hits and has a bend and dent in it which now makes it tuch the gearbox and exhaust.

[jkrzysztof80]

Pm me if you want it.

[billybobboot]

Picture has gone dont mind odd scrape as long as not dented or really rusty. Not sure you can get new ones can you? But yes ill have it as long as not dented or major rusty bit anoyed as mine was ok no rust just the odd scrape till this time.

[jkrzysztof80]

I will take more pic for you when I will get better as I'm lying in bed now.

[billybobboot]

Thats cool no major rush cant fit it till exhaust and under brace arrives

[jkrzysztof80]

Finally I'm better now. Check pictures and let me know if you are still interested.

[Pugme]

Can I ask when you say "no power flow downpipes" mine were made by my local powerflow dealer and are absolutely flawless. Powerflow is obviously a franchise so the work will differ across the country, but mine are fully tig'd and are done in a free flowing Y section.

If you need downpipes I would highly recommend havibg a new set 2.5" to 3" ones made, it made a massive difference to my throttle respone and low end power.

[billybobboot]

i know ive had 2 exhausts by diffent powerflow people (one without knowing as was on ebay)
I just found the one i did have made rubbish build quality was poor.

second off ebay looked nice but went to fit and was poor then found out had 2 diffrent size pipes was ment to be 3" but parts were 2.75.

dont mind but i like to spend money and not have to do the job again or feel i wish i had done something elts.

[billybobboot]

really stuck cusco have stopped doing the 4 point under brace and thre is no stock.


any idea where to get a good quality one from saw rallyart but cant find one for sale want new one!!! i cant use my old one or bend it back i may have to looking to geting custom one made but dont really like that as at lease a mass produced one tends to get a few reviews ect so you kow there ok.

[billybobboot]

yer looks ok little rust but thats only serface how much deliverd

[Pugme]

Rhd japan will be your best bet then buddy if all your local exhaust fabricators arent up to the job.

[billybobboot]

Got a custom one being made from the forum group buy on the exhaust. I dont mind custom made i just am happy to pay for good quality i dont wanna be ripped off but if something is well built ill buy it.