Can someone post a phoy of the ecoscan made cable?, just wondering if I can adapt my VAG cable, or if I need a laptop with two comm ports!!!. I had a look on the limitless site, but couldn't see which was the correct cable?. ta
Can someone post a phoy of the ecoscan made cable?, just wondering if I can adapt my VAG cable, or if I need a laptop with two comm ports!!!. I had a look on the limitless site, but couldn't see which was the correct cable?. ta
Updating Soon!! 1998 Legnum VR4, fully serviced every 4500 miles. Fully Amsoil'd. Falken 453's, EVO 8 FQ320 rear diff.
There are pics here Louis ,post 101 but no idea where that spare wire links too
http://ozvr4.com/forums/showthread.p...evoscan&page=7
AH!, ta for that, looks to me like its a link wire from the OBD11 (duh!) to a conector for the AYC ECU? so you could activate through the main ecu but also the link to the AYC ecu?.
I may try adapting my VAG one?
On mine the link is about 3 inches long and goes to the connector immediately next to the OBDII port.
VR-4 #1 : Ernie, Pyreness Black, 98 Legnum Type-S, Leather, Moonroof & Stainless Sills, Fujitsubo cat back, Apexi RSM - Sold under duress
VR-4 #2 : Wallie, Finesse Green, 96 Legnum Type-S, Erebuni CF bonnet, Profec E-01 & EMB, TRE fuel pump, RPW Downpipes, De-Cat, Fujitsubo Super Legalis R, LC-1, NGK Iridium Plugs, SARD Radiator, Greddy Hard Rad Pipe, ATF Cooler, FMIC, Forge Recirc BOV, KAD 6 Pot 330x28 Brakes, HEL Braided Lines, 17"X8.0 Rota Torques with Wintrac Xtremes, Fully Synth Oils, Ultimate 102RON Fuel, Stainless Sills - Sold after 4 great years
i meant what pin it was linked to in the OBD block if that's where it is attached. naughtika wasn't keen to open his one up to have a look incase he damaged it.Originally Posted by Beastlee
you may be getting wrong end of the stick here as i was lead to believe that the extra connector linked to the big 16 pin connector was only ever used if you wanted to flash your ECU which cannot be done at this time on a mitsubishi legnum/galant. So for a mitsubishi is useless, but i believe the same cable can be used for looking at subaru's ECU which can have the ECU reflashed.Originally Posted by Louis
Bye for Now!
This is why I asked Hamish and he said that this connector was required for comms with the AYC/ABS or he may have meant that only there latest cable will do this.Originally Posted by Davezj
I though he had said it wasn't implemented yet on a VR4
What is the latest version of evoscan at the moment. last i heard it was 2.5 but i have cleared out most of my emails and deleted the limiless ones.
i can't remeber where to download from.
can anyone point me to the correct link. as i don't beleive you can download it from the website you have to do it from an emailed link.
2.6 beta 8 is latest downloadable version. There's a link on the evolutionm forum:http://forums.evolutionm.net/ecuflas...en-review.html
As it's a beta, follow evo4mad's advice just below the download link and use a copy your version 2.5 folder to install it to.
aDe
Cheers aDe
Does anyone know how I can monitor Knock Count in EvoScan? I can't find it as an option. I can only see Knock Voltage and Knock Sum, which I believe is a calculation based on a number of things.
Knock sum is what you want. The raw data is meaningless AFAIK. Knock sum shows the "count" that the ecu takes action over. Below 5 is splendid, over 10 is worrying.
Sorry if I missed it being posted on this thread but I can confirm that the disconnection of pin 9 from the OBDII port allows access to both AYC and ABS ecus from a Limitless 1.3U cable. I will be adding an article soon with the instructions on bleeding the AYC using the actuator control from Evoscan.
does this work with the v6-24, same cable requirements etc? and does anyone know if the ecu is flashable on one?
cheers
ash