Heres a pic of my engine rebuild.
Just doing the Manifold =)
dam, thats one shiny clean 6a13.. whats the plan with the turbos? i see they are not quite the stock item.. do you have anyomre pictures?
i also think at this stage you should take some good pics of the engine.. i can never find any decent picture of the 6a13.. but if you type rb26 you get alot of good pics.. show it off abit lol
photo doesnt do real justice to this rebuild, a live look shows the time and effort that has been put into it, be in next week see the finished article. lol
working on the silver leggy tomorrow, will have those parts for you,
Yeah looks good,definitely put up some more photos!
OnBoost!
Why not become a full member of CVR4,and enjoy the additional benefits? Information here.
To contact the CVR4 Staff please see HOW TO: Contact Committee or Moderators
Good on you for seeing the project through Shane - respect.
More photos would be much appreciated. Good work there Shane.
Well you asked for it so here it goes =)
I dident take any pictures before I started. I think this as about the right order =)
Everything has being striped down cleaned, all seals have being replaced, while keeping everything in spec.
Block has being honed with a deck plane, heads have had a clean and plane with valve stem seals replaced with a valve grind.
Oil pump was striped and repacked with grease.
Crank shaft was thrown on a lathe with a balance.
All new bearing journals with new thrust bearings....etc
I am chasing between 400-500 HP with this build (80hp per cylinder) should be obtainable =)
Thanks Tom =)
Last edited by Fully; 15-05-2011 at 01:45 AM.
Look at the size of that freaking turbo! And you are running a pair of them??!!
thats looks awesome man! are you going be making anymore of those manifolds? im sure there will be interest .. what turbos are you using?
DAT LAG haha hopefully its not to bad for you as mine wont be much better when its done.
as long as you get the runner lengths right it shouldnt be to bad but oh wow are you going to have fun fitting 2 of those between the motor and the suspention tower
No plans on making manifolds, but I will if people want to pay me to make them =)thfelipeth
thats looks awesome man! are you going be making anymore of those manifolds? im sure there will be interest .. what turbos are you using?
T04's.
Yeah it will be fun to see if they both fit. I wont be having all the plastic pipe work in there for a starter and with a manual I think there a bit more room. If it fails I will just go to big singleAdam.Findlay
DAT LAG haha hopefully its not to bad for you as mine wont be much better when its done.
as long as you get the runner lengths right it shouldnt be to bad but oh wow are you going to have fun fitting 2 of those between the motor and the suspention tower
is this a street car or track car or drag car? only ask as if its a drag car you should be going single turbo from square one!... if its a street or track car i can understand the need for the smaller twin setup...
i cant wait to watch this beast running...(its a 7G, aye?) it would be interesting to see how it does down the 1/4mile compared to my car with my P.B. at 12.607 (TD05HR, EVO4) with the extra 500cc on hand it should do well with abit of practice. either way, like i said.. i cant wait to watch this running!
Started the rear bank manifolds today.
if you dont mid me askign what is the rebuild costing you? not including turbo's
day dreaming of 13b's , huge ports and suicide doors, and a few other things too I cant say here.
With turbos I am sitting around the $10k mark. I have a heap of stuff still packed away.
Still need another $1000 for wastegates, flanges, oil lines...etc.
I am am glad the labour is cheap
Thought I would give you an update at were I am, Thanks to Tom (chchthomo) for the parts.
Next is turbos, coolant housing and coil on plug setup =)