Hi all , Pease have you got a link to buy cams gear for the 6a13TT?
Thank's a lot and Merry Chrismass
Saf
Hi all , Pease have you got a link to buy cams gear for the 6a13TT?
Thank's a lot and Merry Chrismass
Saf
One of the Oz guys has just been talking about them
http://www.clubvr4.com/forum/showthr...ring-Cam-Gears
Thank you Sir
Saf
You also can try those for 6a12 from fto's...
Here:
http://www.lelong.com.my/works-t7-ca...-01-Sale-I.htm
Here:
http://www.works-engineering.com/Pro...%20pulley.html
Ex: Galant VR4
Running 268 HP ATW and 443 Nm torque at 0.9 bar
Now: Lancer Evolution 8 FQ-300
Running 325 HP ATW and 510 Nm torque at 1.6 bar
Hey Tomazs , thank's , Cams gear are already ordered ! The first tune will be +1 for intake and -3 for exhaust , this tune give a good power for the 6G72 with stock cams.
Saf
^ did you buy the works engineering ones discussed in the links above? if so when you get them I would be intrested in seeing some pictures of how good the belt fits into the teeth and so on before I commit to getting a set for my 6A13
Seconded, pics and impressions would be appreciated
No problem , i'll post some pictures when i'll received the cams gear and the instalation , also i'll give you the best tune when the car will be on the dyno ... The 6G72 like +1 for intake and -3 for exhaust , it's the best tune to take the more power but i saw on my garage that other car are different , and if you put +1 for intake you'll lose vacuum and the final goal for the power will be not good ! Anyway i'll give you my result to take the maxim power and to have a nice drivevebility!
Saf
Ps: Hope that all are understand , because my english it's bad!
Your English is fine
Look forward to hearing the results
any luck with getting some pics yet SAF68?
Any update on this.
Just installed my cams so next valvetrain mod will be gears
cheers
Seconded.
Just ordered mine set of cam verniers. And wonder what would be the best setting for 6A13TT.
it would be ineresting to see the advantage of the adjustable cam gears particularly on a tuned car like your tomazs
Bye for Now!
More overlap or/and to adjust the cams with degree wheel
Saf
3000GT 1430awhp and 1132nm twin 6466CEA @ 44 psi + Galant VR4 type-S 701awhp @ 1.7 bars 6466CEA + Galant GDI to 4G63 ... In progress
In a very simplistic way of describing it, because I don't really understand this at the moment.
When you adjust the cam gears, do you actually gain anything, or do you move where the torque is created/brought in.
E.g. Move it from low down touque to much higher in the rev range, where the 6a13tt is lacking it.
When you adjust cams gear , you can create more overlap if you run on stock cams :
Overlap –
This is the number of degrees that the intake and exhaust valves are open at the same time. A cam with timing of 25-65-65-25 has (25 + 25) = 50 degrees of overlap. Overlap is the most important parameter effecting idle and off idle quality. A large overlap causes a rough or lopey idle. Increasing the duration or decreasing the lobe separation cause an increase in overlap .
For all !! Don't buy a gams gear with 2° range /mark
DaveZJ , you'll understand with this link
http://www.enginebasics.com/Advanced...%20Tuning.html
If you buy billet cams shaft , you'll need to buy cams gear to check the correct timing
http://www.youtube.com/watch?v=55kgprdD6t0
Saf
Hey tomasz ,
What is your setting?
Saf