Ported Cylinder heads!

[Adam.Findlay]

Have a set of ported cylinder heads for sale.
they are not quite finished yet as the final state of them will depend on what the buyer wants.
The porting on the heads themselves is almost all finished.
They will come with a fresh 3 angle valve seat cut and resurfaced valves, also will be freshly surfaced and cleaned. so

can also come with

-New valve stem seals
-Heavy duty valve springs
-Billet cams (http://www.clubvr4.com/forum/showthr...883#post761883)
-262 regrind cams
-Lifters

Price is obviously dependent on what you want with them,
Just the bare heads will be cheaper than if you want the works, ie complete heads with springs, lifters, cams and valves as a "ready to go bolt on"


PM me or txt me on 0277107477 if your intrested

am willing to ship overseas also at the buyers expense of course.


Will update thread with pics when the port work is finished, and the heads are cleaned (as they are dirty and yuck looking at the moment)

[Adam.Findlay]

Right here are some pics of the ports. and pics of a stock head for comparison sake.


righto
to start off with heres some pics of the stock head
1-stock combustion chamber

http://i693.photobucket.com/albums/v...901_135100.jpg

2-looking down the guts of stock intake ports

http://i693.photobucket.com/albums/v...901_135144.jpg

3-looking down the stock exhaust ports

http://i693.photobucket.com/albums/v...901_135133.jpg

4-casting marks on the intake ports. (didnt bother taking pics of the exhaust port casting marks as there was too much carbon build up.

http://i693.photobucket.com/albums/v...901_135150.jpg
http://i693.photobucket.com/albums/v...901_135237.jpg

Now onto the exciting pictures..

5-half finished combustion chamber next to a un touched one for comparison. as you can see the nasty lips around the valve seats are smoothed off

http://i693.photobucket.com/albums/v...901_143214.jpg

6- completed combustion chamber, all the sharp edges smoothed off and polished up, also shows the smoothing off done to the end of the valve guides.

http://i693.photobucket.com/albums/v...901_124903.jpg

7-looking down the exhaust ports

http://i693.photobucket.com/albums/v...901_124936.jpg

8-looking down the intake ports

http://i693.photobucket.com/albums/v...901_124947.jpg

9-Intake port, see how the bump before the valve guide has been blended into the rest of the port and the guide itself has been shaped a bit nicer then stock. also the ground out the ID of the valve seats as stock they have a nasty lip where the seat has been machined into the head. but now they are all smooth and polished up. also all of the tight radius's have been re-done to provide a much straighter path for the air to flow.

http://i693.photobucket.com/albums/v...901_124744.jpg

10- Exhaust port. much the same as the intake

http://i693.photobucket.com/albums/v...901_124843.jpg


That about sums it up.
Would like $2000NZD for the ported heads assembled which will be
-acid cleaned
-fresh 3 angle valve job
-refaced stock valves
-skimmed head-gasket surface for MLS head gasket
-Heavy duty valve springs
-New Valve stem seals
-Brand new zero tick lifters

so all you would need to do it put rocker arms and cams in and bolt them down

if you do want cams also Ill throw in some cam seals with it.

[Adam.Findlay]

Bump!

[Adam.Findlay]

bump

[Adam.Findlay]

bump with pics of the fully machined heads with de-carbon'ed and refaced valves

[dutch driver]

what's the price for a complete done job on the heads?
without shipping.
cheers

[Adam.Findlay]

Would like $2000NZD for the ported heads assembled which will be
-acid cleaned
-fresh 3 angle valve job
-refaced stock valves
-skimmed head-gasket surface with fine finish for MLS head gasket
-Heavy duty valve springs
-New Valve stem seals
-Brand new zero tick lifters

so all you would need to do it put rocker arms and cams in and bolt them down

if you do want cams also Ill throw in some cam seals with it.

The cam regrind for 262 degrees and 9.8mm lift will cost you $600NZD + the cost of stock cams

or go for a much larger profile on the billet cams I also have for sale here
http://www.clubvr4.com/forum/showthr...883#post761883

[Fully]

Are you flow testing these ported valve inlets?