Hi all,i am seeking some info on the prism conrods for the 6A13....
Is there anyone in this group using those ?
Any info will be greatly appreciated...
Hi all,i am seeking some info on the prism conrods for the 6A13....
Is there anyone in this group using those ?
Any info will be greatly appreciated...
I think Adam Findlay used them on one of the engines he built.
But I think he had to machine the width down on the rods he bought for some reason.
The thread is on here somewhere.
Plus Adam Findlay is not active on here as he uses ozvr4 for obvious reasons.
Sent from my MI 5s using Tapatalk
Bye for Now!
there must be someone here thats using these rods to give me some info.....
Yes I use it, already hit 5000 km with it with no issue like adam experienced. just buy on ebay its cheaper than before already. I bought forged CP piston on rpw, because they had it ready to ship. I must say CP piston product quality awesome. my advice buy CP piston with 0.50 OS and with at least 9 compression ratio (CR). I bought 0.5 OS 8.5 CR CP piston spec and felt sorry, because turns out i need 9 CR for my ported TD03 turbo with more lag. if you buy 9 CR piston that u should gain the power earlier compensate for lag turbo. If you want to stay with stock piston than ask the prism seller to make the rod with fix piston pin like the stock piston. he also offer the rod bolt but of course with less strength than ARP. They say stock piston would handle up to 500 hp. but thats ur choice, because forged piston shoud require more $$$$
http://www.ebay.com/itm/FORGED-RODS-...AAAOSwlV9WSGkn
Last edited by ersanalamin; 08-08-2017 at 07:48 AM.
OOOhhh, Not a bad price those. Stop spending money I havn't got.
Have you tried running pass 7000 rpm ?
My aim is 560whp but I working with a budget so I am liking the cost of these rods.....
I passed 7500 rpm ocasionally, its daily driven car BTW. How much is your budget? If your car fully stock VR4 then for 560 whp You would spend at least 10.000 USD for parts, services and supporting mods exclude mechanic man hour. Thats for engine supporting mods only. I spent 6800 AUD for CP Piston, Prism Conrod, ARP head stud, crank/main stud, conrod bolt, ported twin turbo, Adams 264 regrind cam, BC Crower valve spring, forge motorsport twin adjustable wastegate and AEM WAI. Then you would need uprated fuel pump, let say aeromotive fuel pump and TME Steve 1000 cc injector. I havent bought 2 last item but would cost 1100 AUD. next perhaps MAF to MAP conversion need at least 500 USD Thats my aim for 450 whp.
Last edited by ersanalamin; 09-08-2017 at 01:09 AM.
Currently @ 410whp gonna re tune for 460 whp.
At that point I know I will be at the limit so plan is to build a forge block....
Single garrett GTW6262 twin scroll
Custom manifolds and intake
Twin 38mm wastegates
Mishimoto Intercooler
Tial BOV
ID 1000cc injectors
Stock intake pump feeding a surge tank with 320lph AEM external fuel pump
Aeromotive fuel reg
Custom fuel loop
Russell fuel filter / full braided lines
-8an feed -6an return
Stock head and block just fitted head studs.
Custom COP setup
Full 3" exhaust system
AEM water meth kit
Greddy profec boost controller.....
OSGIKEN twin disc clutch kit
And some more just can't remember all at the moment....
Hmmmm....just wondering why don't use the greddy??
The stock ECU can control boost much more safely than an aftermarket one. Or if you've got an aftermarket ECU, best to use that for boost control for the same reason. They'll have safety features built in which may one day save your engine!
Have no issues with boost control just abit lazy on low end bur crazy on top...might use a 63 rear end next and get the power abit earlier as its a street car / daily driven vehicle
Hello. Anybody knows is it the same rods as prism, or it's just a copy with worth quality?
https://russian.alibaba.com/product-...466b701dojbtrB
Maybe somebody actualy use it?